HARDINGE BROTHERS, INC. ELMIRA check the part description to make certain the assembly and/or individual part applies to your machine. .. Bed. 2. Screw. 2. Washer. Front Screw. Lock Washer. 6. 14 D V. 0 0 1 0 2 1 4. D V B 0 0 0 9 7 7 6. 0 5 5 0 3 0 5. N 3 7 0 0 0 0 7 3 6. 5 p. 0 0 0 6 4 3. HARDINGE DV59 DSM59 Lathe Part Manual DV DSM [Misc.] on Amazon. com. *FREE* shipping on qualifying offers. Number of Pages: 15 This is a. DV59 Precision Lathe and DSM This is a reproduction, not a photocopy, of an original Hardinge DV59 Precision Lathe and DSM59 Second Operation.
|Country:||Republic of Macedonia|
|Published (Last):||19 May 2004|
|PDF File Size:||18.99 Mb|
|ePub File Size:||1.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Remove back motor panel 4. Hardinge 6 position turret. Take gearbox off if changing the top spindle belt 3. Browse Related Browse Related.
Now, it you make the block that is attached to the free ballnut spring loaded with a torsion spring, it will hold the “free” dv-95 against the red block. Not sure how that is done but it seems it can be. Board index All times are UTC.
Vertical Mill, Lathe Project Log > CNC’ing a Hardinge 2nd OP DV Lathe – Page 3
I stare into the headstock and for the life of me I am missing something, I see no setscrews or spanner to loosen the spindle pulley. Read over relative threads, not just this one but others here as well and then you will be in a better position to begin how best to accomplish the conversion. Also shop in Also shop in.
More than just a pretty picture.
Hardinge Dv59 Dsm59 Lathe Part Manual Dv-59 Dsm-59 0334
If you have specific questions, someone will likely be able help. Results 1 to 12 of When it came time time get the belts off this I was scratching my butt for a while before I remembered the shaft pulling out of the bearing.
A few details first: Due to the size of this slide, Hardigne do not like to modify this slide but intend to proceed as follows: To make this work, a new male dovetail and flat gib will have to be made along with some screws etc that will need to be modi Most of the manuals I reproduce look better than their originals.
Phase II On successful completion and testing of the above, I will proceed to raise the height of the spindle head by providing spacer on the bed hardine the spindle will be driven by a servo motor of suitable power. List your items fast and easy and manage mahual active items.
The hardingge screw is mounted in the two end plates in two angular contact ball bearings Hardinge DV59 Refine Results. This system attaches to the spind All of the manuals are printed on thick white paper to withstand shop wear and tear.
Stepper motors will be mounted on both axis of the table, directly coupled to the ball screws if space permits, or else through timing belt and pulleys. It clamps to the bed, it does not bolt to it in the 4 corners as the newer ones did ken wrote: I have collected this information for many years and have found the information they contain to be priceless in using and setting up the machines properly. The bed width is approx. Ships on time with tracking, 0 problems with past sales.
If my mill had sufficient travel to mill flat and parallel in one operation the relief for the THK rails and lathe body I would probably still use it. Will load on your truck for free! What software are you using? I also feel the servos will be a better way to go, but a final evaluation is yet to be done. The time now is Powered by eBay Turbo Lister The free listing tool.
HARDINGE DV59 DSM59 Lathe Part Manual DV-59 DSM-59 0334
The above arrangement will give sufficient place on the longitudinal slide of the table to mount three or four tools and hardinve of mounting a live tool also. Intermediate shaft slides side to side.
This was on his showroom floor so we believe it to be working. I do have the carriage blocks drawn up and tool paths for manula they get machined.